The study was carried out as a time study of five wood chippers placed on trucks,so?called huggbilar. They are trucks with built?in wood chipper, chip bowl and crane pulling a chip trailer. The system is used for chipping wood fuel, transporting, and delivering the chips to heating plants.

Tomo Hugglink (TOMO Skog) is an innovation for harvest and transport of biofuels. The system consists of a truck, a chipping unit and crane mounted on a link and a wood chip trailer. The system works in such a way that the chipping unit is disconnected and placed on the site and wood chips are loaded directly into the wood chip trailer.The aim of this study was:- To examine the performance of the TOMO Hugglink system under different conditions such as the size, placement and quality of the pile.- To calculate the cost per raw ton for two vehicle combinations at different transport distances and to examine the effect of a reduction in set-up time and an increase in load weight.- To identify possible improvements with the TOMO Hugglink system.A time study was conducted within the thesis work to make it possible to determine production and time consumption. In the subsequent economic analysis the cost per tone at different transport distances was calculated for two different lorry concepts. Furthermore the effect of a reduction in set-up time and an increase in load weight was calculated.Under current conditions the utilization of the chipper is low and only 29 % of the total system time is occupied by chipping.

Piles of deadwood are often retained in forests after management to support the biodiversity ofsaproxylic organisms which depend on deadwood to survive. Any knowledge about the crucial role ofpiles as suitable habitat of saproxylic organisms compared to single distributed deadwood objects thatare around the piles would help conservation actors to motivate more forest owners to supportsaproxylic organisms during their management. Therefore to give facts to this the saproxylic fauna ofdifferent pile positions (up and low) was studied and compared to distributed deadwood samplesaround each pile. Our study was focused on saproxylic beetles. Some other parameters such asdiameter, deadwood volume, pile volume and decay stage were assessed to define any effect.

This paper deals with the question of with witch tools the Alvastra pile dwelling was built. To reach a result I calculate the curvature on 29 stone axes, 8 double-edged axes and 21 simple-edged axes, used in the middle-neolithic in what today is Sweden. These results are then compared with two jams (the point in the pole where the axes edged stopped and left a mark) on two piles from Alvastra pile dwelling..

Stump wood is a hot alternative when the heating plants demands more and more forest fuel. The aim with the study has bean to calculate the costs in four different systems for transportations of stump wood, examine if there are any differences in fuel quality for the stump wood in the different systems, analyse if the fuel quality in stump wood is affected with the time it lays by the road side and how much space the stump wood demands on the road side. To calculate the costs for the different systems a system analysis was carried out, where some of the costs were collected through field studies on Holmen Skog stump experiment and other costs were collected from literature and contacts. Data for the fuel quality study was collected from Eons heat plant in Norrköping. Data for the study of how much space stump wood takes along a roadside was collected from field studies.

This report deals with the design of a controller for SmartMedia? flash memory cards, based on a hardware description found in the SmartMedia? Interface Library - SMIL. The design was made on logic gate level, using standard cells in OrCAD Capture. After simulation of the design in PSpice A/D, it was exported as an EDIF netlist, which was used to make a chip layout in L-Edit, a layout tool for making integrated circuits. The layout was made using a method called Standard Place and Route - SPR, where the layout tool places standard cells from a library and connects them according to the EDIF netlist.

Piled friction soil show a set-up which is increasing with the time after installation. The cost could be reduced if the set-up had been taken into account when designing but in Sweden it is very unusual to do that. Previous studies showed that set-up can vary between 25 % and 75 % during the first 90 days after pile installation. This showed that the effect of the phenomenon is difficult to predict. A study involving five projects have been carried out by specifying certain parameters like pile type, method for pile installation and test method for measure the bearing capacity in friction soils located in Sweden.

Storage of biomass is often associated with problems such as heat development, dry matter losses and reduction of fuel quality. The rise in temperature can potentially cause a risk of self-ignition in the fuel storage. Moreover, emissions from storage piles can cause health problems in the surrounding. The dry matter losses and reduction of fuel quality can have economical effects. The aim of this thesis project is to develop guidelines on how to store large amount of biomass at Vattenfalls heat and power plants in an optimal way.

This report is a bachelor's thesis of two students from the Energy and Environment degree at KTH Stockholm. Grinda is an island situated Stockholm archipelago. Skärgårdsstiftelsen is landowners and manages the area. Grinda Wärdshus, a guest house located in the island, currently uses an oil-fired boiler as a heating system. The aim of this thesis is to investigate whether wood chips or pellets is, from a sustainability standpoint, a suitable heating method for the guest house.

At the Skoghall pappermill, sulphatepaper pulp is produced in a continuous digester originally from 1969. To be able to maintain a high level of production there is a need for a process with few disturbances. Variations in how well the wooden chips are packed in the digester is one form of disturbance. Today there are no available measurements on how well the chips are packed. Instead this is regarded as being constant.

The moisture content in 10 deliveries of tree parts and 10 deliveries of wood residues were measured with different methods to analyze the quality of procedure used at Dåvamyran today. At the same time a survey was made on the measure procedures used at heating plants in Sweden The majority of the heating plants in Sweden use weight and moisture content as base for payment but at some plants only volume. The moisture content is usually estimated by drying wood chips in an oven but few plants a visual estimation is used. At few plants moisture content is estimated spectroscopicily. The techniques using near infra read light and other electromagnetic are still at a test stage. The methods of measurement used today are quit unreliable for the individual deliveries and there is a risk for systematic mistakes.

Bioenergi är en stor industri i Sverige och står för en betydande del av energiomsättningen. Bioenergi i form av flis förvaras runt om i landet på hög i väntan på förbränning. Då högarna läggs upp startar olika processer som värmer upp stacken, ofta till temperaturer på 50°C under det första dygnet. En vanlig ansats i litteraturen är att denna temperaturstegring beror på aerob nedbrytning. Arbetet ämnar undersöka om denna uppvärmning endast beror av mikrobiella aktiviteter.

This thesis describes how the chip space and coolant channels are designed in today?s mills, the ideas behind the design and what is considered to be the best method of cooling. It contains ideas on how the chip space can be simplified. It contains several concepts on how the cooling could be designed for better efficiency and manufacturability. There are also suggestions on how the cooling could be stopped when the cutter isn?t cutting.

The purpose of this study is to explain how the value of sawn wood changes when sawn wood are cut in 30 respective 60 cm lengths. The raw material into the saw mill will mainly be bucked in 30cm and 60 cm modules. There will also be two alternatives where the timber will be bucked special lengths, 370, 490 and 550 cm but also in 490 and 550 cm.The method used for the study is to simulate both cutting and sawing the woods. For cutting the simulator Timan is used and for sawing the simulator Timberopt is used. When data is generatedfrom the simulators, calculations of some key figures is done and also how much the revenue need to be increased for the sawn wood in order to cover for the increased costs of changing sawn woodfrom 30 cm to 60 cm modulesThe conclusion is that the single biggest reason, impacting the value of the sawn wood is the cutting at the saw mill.When going from 30 to 60 cm modules, the impact will be that the customers to the saw mill must pay more to increase the revenue by at least 10% for the sawn wood in order to justifice the changein production.It is also possible to increase the value of the products further by bucking the timber in three lengths, 370, 490 and 550 cm, in order to get 12 % increase of the share of longer sawn wood (>= 480 cm)..

Fire is an important ecological factor, but its consumption of coarse woody debris, CWD, has hardly received any attention. In this study, I investigate the consumption in relation to the time of initial flame exposure and propensity for continued combustion of standing CWD of pine (Pinus sylvestris). Two types of CWD were studied. Firstly, wood that had been dead for one to ten years. Secondly, wood that had been dead for several decades. In the burning experiments, logs of approx.